Measurement of residual stresses in dissimilar friction stir-welded aluminium and copper plates using the contour method

The longitudinal residual stresses in the friction stir-welded plates of 5A06 aluminium and pure copper were determined using the contour method. The results revealed the presence of high tensile and compressive residual stresses on the aluminium and copper sides, respectively. The residual stresses were detected on the weld zone as well as the thermo-mechanically affected zone (TMAZ) of the aluminium plate. In contrast, the compressive residual stresses in the copper plate had a much narrower width along the weld line. Peak tensile stresses up to 240?MPa were found in the TMAZ of the aluminium plate.     

Effect of metallurgical evolution during post-weld aging treatment on localised corrosion of resistance spot welding joints of A286 superalloy

The combined effect of resistance spot welding and precipitation hardening on the localised corrosion of A286 superalloy is studied. The specimens tested by double loop electrochemical potentiokinetic reactivation were welded in the solution treated condition, and then subjected to different precipitation hardening treatments. For both base metal and weld nugget, the maximum localised corrosion is reached when η phase is clearly observable. The fact that the localised corrosion resistance of weld nugget is different from that shown by base metal may be explained by the segregation of Ni and Ti towards the interdendritic region of weld nugget (studied by using scanning electron microscope/energy dispersive X-ray analysis).     

热轧带钢卷取机夹送辊修复材料与再制造工艺研究

为了提高热轧带钢卷取机夹送辊表面的修复质量，通过正交试验优选出埋弧堆焊专用焊丝ZJ－11和ZJ－12，过渡层选用ZJ－11药芯焊丝，堆焊硬层选用ZJ－12药芯焊丝，采用优选出的焊丝进行了堆焊修复试验。试验结果显示，堆焊焊缝金相组织中的马氏体更加细化，且碳化物颗粒明显增加，材料的硬度与耐磨性显著提升。研究表明，通过采用合理的再制造工艺对热轧带钢卷取机夹送辊进行修复，修复后满足要求，使用效果良好，显著提高了夹送辊的使用寿命。     

双光束激光焊匙孔动态特征分析

文中研究了高功率单光束激光焊与双光束激光焊过程中匙孔动态特征的差别. 结果表明，单光束激光焊及双光束激光焊接过程中匙孔均处于从产生到湮灭的剧烈波动的过程，不同于单光束激光焊匙孔的形成、长大、维持、缩小、湮灭过程，双光束激光焊的匙孔还存在分离长大及合并缩小的过程；在相同的焊接参数及焊缝具有相同熔深的条件下，双光束激光焊匙孔的波动频率约为单光束激光焊的2/3，单光束激光焊匙孔的开口面积均值约为双光束激光焊匙孔开口面积的1/2，开口面积的波动变异系数约为单光束激光的2倍，即双光束激光焊过程中匙孔较单光束激光焊的具有较高稳定性.     

Process and joint quality of ultrasonic vibration enhanced friction stir lap welding

In order to improve the process effectiveness and joint quality, ultrasonic vibrations were integrated with friction stir lap welding. Effect of ultrasonic exertion on the process and joint quality of AA 6061-T6 were investigated. Upon ultrasonic exertion, joints owned larger effective lap width, shorter hooks and improved strength. Weld fracture mode changed from a ductile–brittle mixed mode to a more ductile mode while the fracture path shifted from lap interface to beyond the stir zone. Material flow and interface defects were characterised using lap welded dissimilar aluminium alloy joints. Ultrasonic vibration improved the material flow and reduced the interfacial defects. Variations in failure load of joints were found in accordance with the variations in material flow and interfacial defects.     

焊丝中Si元素含量对铝合金接头裂纹敏感性的影响规律及机理

使用扫描电镜、能谱、温度场实时采集等测试方法，研究了焊丝中Si含量对AA6063铝合金GMAW焊接头热裂纹敏感性的影响规律及机理. 结果表明，当焊丝为纯铝时，鱼骨试样的焊缝中心会出现细长的焊接裂纹；当焊丝中的Si含量为4.5% ~ 6%时，裂纹的长度变短，但是开裂距离明显增加；当焊丝中的Si含量达到11% ~ 13%时，试样焊缝无裂纹出现. 随着Si含量的不断提高，合金易出现裂纹的凝固温度区间先增大后减小；焊丝中Si含量的不同还会影响凝固后期金属液的流动性，使得焊缝晶界处的物相成分和形态都有明显的区别；同时，Si含量的提高会使得接头的冷却速度先增加后减小，从而导致应力状态改变，热裂纹敏感性先升高后降低.     

API X52管线钢与Corus RQT 701超高强钢的焊接工艺

针对超高强钢在机械行业的广泛使用,焊接接头易出现淬硬脆化、裂纹等缺陷的情况,采用焊条电弧焊(SMAW)和药芯气体保护焊(FCAW-GS)组合的焊接方法,对API X52管线钢与Corus RQT 701超高强钢的焊接进行了工艺试验,并进行常规力学性能试验。结果表明,通过合理匹配焊接工艺参数,严格控制低热输入量及层间温度,实现了小熔合比的异种钢焊接,且焊接接头具有良好的力学性能,达到了标准和规格书的要求;异种高强钢焊接,采用SMAW打底焊接和FCAWGS填充并盖面的方法,焊接效率较单纯采用焊条电弧焊工艺提高2倍以上。     

Plasma Unesterified Fatty‐Acid Profile Is Dramatically and Acutely Changed under Ischemic Stroke in the Mouse Model

Although plasma biomarkers would facilitate rapid and accurate diagnosis of ischemic stroke for immediate treatment, no such biomarkers have been developed to date. In the present study, we tested our hypothesis that plasma unesterified fatty acids (FFA) are altered at early stages of acute ischemic stroke. Plasma was collected from mice 2 h after the permanent middle cerebral artery occlusion (pMCAo) onset, as well as from sham operated and control animals. After 2 h, pMCAo significantly changed the plasma FFA profile with the most dramatic 2‐ to 3‐fold relative increase in very long n‐3 and n‐6 FFA including 20:4n‐6, 22:4n‐6, 22:5n‐6, and 22:6n‐3. Changes in the plasma FFA profile are consistent with FFA liberation from brain phospholipid hydrolyzed under ischemic insult. These results identify, for the first time, the plasma FFA profile as a potential biomarker for an early ischemic stroke within the therapeutic window for thrombolytic treatment. Further studies are required to confirm its specificity and sensitivity in clinical settings.     

一种液压摩擦焊机电液系统研究与试验

针对海上石油平台、海底输送管线维修的需要,提供了一种液压摩擦焊机液压和电器系统设计思路,通过参数计算、电液控制系统设计,研发了一种液压摩擦焊机,通过对DH38钢摩擦叠焊单元成型工艺试验,发现焊接接头拉伸强度达到了母材强度的76%以上,验证了液压摩擦焊机的可靠性能,通过该研究的应用,可对海上石油平台、海底输送管线的维修起到积极作用。     

H13钢等离子堆焊Ni60A/Cr3C2覆层的磨损及热疲劳性能

采用等离子堆焊技术在H13钢基体表面上制备了Ni60A/Cr₃C₂堆焊覆层,研究了覆层的磨损行为和热疲劳性能。在600 ℃下销盘试验的结果表明,镍基碳化铬复合覆层的耐磨性是Ni60A堆焊覆层的2.8倍和基材H13钢的11.6倍。镍基覆层可以显著降低H13钢的摩擦因数,加入碳化铬则会削弱覆层的摩擦性能。随着磨损的进行,主要磨损机理从氧化磨损演变为磨粒磨损和粘着磨损。在800 ℃到室温下的热疲劳测试结果表明,镍基碳化铬复合覆层在48个热循环后疲劳裂纹达到200 μm,早于镍基覆层的62次。这说明高温氧化促进热疲劳裂纹的产生。碳化铬增强相从镍基上剥离,导致镍基复合覆层热疲劳性能下降。